Jump to a term: A2L Refrigerant · AFUE (Annual Fuel Utilization Efficiency) · AHRI Certificate · Air Handler · B-Vent and the Wye Fitting · Balance Point (Switchover Temperature) · BTU (British Thermal Unit) · CFM (Cubic Feet per Minute) · Cold-Climate Heat Pump · Combustion Air · Commissioning · Compressor · Condensate Pump · Condenser · Condensing Furnace (High Efficiency) · Defrost Mode · Disconnect · Dual Fuel · Duct Sealant · Evaporator Coil · Filter and MERV · Flue · Freon · Heat Exchanger · Heat Pump · Heat Strips · Line Set · Manual J (Load Calculation) · Mini-Split (Ductless) · Permit and Inspection · Plenum · R-22, R-410A, R-32 and R-454B · Refrigerant · SEER2 and HSPF2 · Short Cycling · Single-Stage, Two-Stage and Modulating · Static Pressure · Superheat and Subcooling · Supply and Return Ducts · Ton · Ultra-Low NOx Furnace · Variable-Speed vs Multi-Speed Blower Motor · Zoning and Dampers
BTU (British Thermal Unit)
The official definition: "The quantity of heat required to raise the temperature of one pound of water one degree Fahrenheit." (Merriam-Webster)
In plain English: A BTU is a small unit of heat. When you see a furnace rated at 80,000 BTU, that's how much heat it can put out in an hour. For an air conditioner or heat pump, it's how much heat it can move out of (or into) your home in an hour.
Why it matters to you: BTU is the size of the system. Too big and it short-cycles, wears out sooner and leaves rooms uneven. Too small and it runs nonstop on the coldest or hottest days. The right number comes from measuring your house (a load calculation), not from what was there before.
Ton
The official definition: In HVAC, one ton of capacity equals 12,000 BTU per hour. The name comes from the heat it takes to melt one ton of ice in a day.
In plain English: Tons are just a shorthand for sizing AC and heat pumps. A 3-ton system moves 36,000 BTU an hour. Tons and BTU describe the same thing, the way a dozen and 12 do.
Why it matters to you: When two quotes are different sizes, they aren't the same job. And rebates like Xcel's pay per ton, measured at 5°F, so size changes your rebate too.
CFM (Cubic Feet per Minute)
The official definition: A measure of airflow: the volume of air, in cubic feet, that moves past a point each minute.
In plain English: CFM is how much air your system pushes through the ducts. A rough rule of thumb is about 400 CFM per ton of cooling.
Why it matters to you: A new system is only as good as the air it can move. If your ducts are too small for the new unit, it'll be noisy, less efficient and harder on the equipment. That's why we check ductwork before we quote.
Refrigerant
The official definition: A substance used in a refrigeration cycle that absorbs heat as it evaporates and releases it as it condenses.
In plain English: Refrigerant is the stuff that carries heat. In summer it picks up heat inside your house and dumps it outside. In a heat pump in winter, it does the reverse.
Why it matters to you: Your system is built for one specific refrigerant, and the price per pound varies a lot between types. If a repair quote mentions refrigerant, ask which one and how many pounds.
Freon
The official definition: A trademarked brand name for a family of refrigerants, most famously R-22.
In plain English: Freon is a brand name, like Kleenex. People say it for any refrigerant, but almost nothing being installed today uses it.
Why it matters to you: If a quote says "Freon, $300 a pound," you can't price-check it, because that's probably not what's in your system. Ask what refrigerant it actually is (it's printed on the outdoor unit's label).
R-22, R-410A, R-32 and R-454B
The official definition: Refrigerant designations under the ASHRAE numbering system. R-22 was phased out of new US equipment in 2010 and production ended in 2020. R-410A replaced it and is now being phased down in new equipment. R-32 and R-454B are the newer, lower-impact refrigerants used in today's systems.
In plain English: These are generations. R-22 is the old stuff, R-410A is what most systems from the last 15 years use, and R-32 and R-454B are what new systems use now.
Why it matters to you: If you have an R-22 system with a leak, the refrigerant alone can cost more than it's worth. Often a new R-454B or R-32 system makes more sense than recharging an old one.
Heat Pump
The official definition: A device that moves heat from a cooler place to a warmer place using a refrigeration cycle, and can reverse to provide either heating or cooling.
In plain English: A heat pump is an air conditioner that can also run backwards. In summer it moves heat out of your house; in winter it pulls heat in from outside, even when it's cold out.
Why it matters to you: People hear "heat" and think it replaces the furnace. It actually replaces your air conditioner, and it can take over some or all of your heating too. That's why it's the system most rebates are aimed at.
Dual Fuel
The official definition: A heating system that pairs an electric heat pump with a fuel-burning furnace, switching between them based on outdoor temperature or cost.
In plain English: A heat pump and a gas furnace working as a team. The heat pump handles most days, and the furnace takes over when it gets really cold.
Why it matters to you: It's a good middle ground in Denver. You keep a gas backup for the coldest nights, and you still qualify for many heat pump rebates. An electric-only heat pump does all the heating itself, often with electric backup strips.
AFUE (Annual Fuel Utilization Efficiency)
The official definition: The ratio of a furnace's annual heat output to the fuel energy it consumes over a year, expressed as a percentage.
In plain English: AFUE is how much of the gas you pay for actually becomes heat in your home. An 80% furnace turns 80 cents of every gas dollar into heat; the rest goes up the flue.
Why it matters to you: An 80% furnace is a standard efficiency model. Anything 90% and up is high efficiency, and it costs more up front but less to run. Going from 80% to 90%+ usually needs new venting, which adds to the price.
Condensing Furnace (High Efficiency)
The official definition: A furnace that captures additional heat by condensing water vapor out of its exhaust gases, typically achieving 90% AFUE or higher.
In plain English: A high-efficiency furnace squeezes so much heat out of the exhaust that the exhaust cools down and turns into water. It has a second heat exchanger to do that.
Why it matters to you: You can usually tell what you have by looking. A high-efficiency furnace vents through white PVC pipes, often one for exhaust and one for fresh air, and it has a drain line for the water. A standard 80% furnace vents through a metal flue.
Heat Exchanger
The official definition: A device that transfers heat from one medium to another without the two mixing.
In plain English: In a furnace, the heat exchanger is the metal chamber that gets hot from the burning gas. Air from your house blows over the outside of it and warms up, while the exhaust stays inside and goes out the vent.
Why it matters to you: A cracked heat exchanger can let exhaust gases, including carbon monoxide, mix with your air. It's a serious finding, and it's usually a reason to replace the furnace. Ask to see it if someone tells you yours is cracked.
Evaporator Coil
The official definition: The heat exchanger in a cooling system where liquid refrigerant evaporates, absorbing heat from the air passing over it.
In plain English: The coil is a radiator-looking box that usually sits on top of your furnace. Cold refrigerant runs through it, and your furnace fan blows house air across it to cool it down.
Why it matters to you: The coil has to match the outdoor unit. A quote that replaces the outdoor unit but keeps an old coil may save money today and cost efficiency and reliability later.
Condenser
The official definition: The component of a refrigeration system where refrigerant vapor releases heat and condenses into a liquid.
In plain English: The condenser is the outdoor unit with the big fan on top. It's where the heat pulled out of your house gets dumped outside. On a heat pump, the outdoor unit does both jobs, depending on the season.
Why it matters to you: Keep it clear of leaves, snow drifts and plants, and don't let it sit in a puddle. A blocked outdoor unit works harder and can void some warranties.
Single-Stage, Two-Stage and Modulating
The official definition: Classifications of furnace gas valves by heat output. A single-stage valve operates at one fixed output. A two-stage valve operates at a low and a high output. A modulating valve adjusts output in small increments across a range.
In plain English: Single-stage is a light switch: on or off. Two-stage has off, low and high. Modulating is a dimmer, with dozens of small steps, so it can run at exactly what your house needs.
Why it matters to you: More stages means steadier temperatures, quieter running and fewer drafty swings. It also costs more. For many Denver homes, two-stage is a good balance; modulating is the premium choice.
Variable-Speed vs Multi-Speed Blower Motor
The official definition: A multi-speed motor runs at a few fixed speeds. A variable-speed motor, usually an ECM (electronically commutated motor), adjusts its speed continuously to deliver a target airflow.
In plain English: The blower is the fan that pushes air through your ducts. A multi-speed fan has a few settings, like a box fan. A variable-speed fan can run at almost any speed, and it adjusts on its own.
Why it matters to you: They sound the same, but they're not. A variable-speed blower uses less electricity, is quieter, and does a better job pulling humidity out in summer. It pairs best with a two-stage or modulating furnace.
SEER2 and HSPF2
The official definition: SEER2 (Seasonal Energy Efficiency Ratio 2) rates cooling efficiency over a season. HSPF2 (Heating Seasonal Performance Factor 2) rates a heat pump's heating efficiency. The "2" versions took effect in 2023 under updated Department of Energy test procedures.
In plain English: These are the miles-per-gallon ratings for air conditioners and heat pumps. Higher is more efficient.
Why it matters to you: Compare quotes using the same rating version. A SEER number and a SEER2 number aren't the same scale, so a "16 SEER" and a "15.2 SEER2" system can be roughly equal.
AHRI Certificate
The official definition: A certificate from the Air-Conditioning, Heating, and Refrigeration Institute listing the tested, certified ratings of a specific combination of indoor and outdoor equipment.
In plain English: It's the official spec sheet for your exact matched system, not just the outdoor unit.
Why it matters to you: Rebates usually require it, and it's the easiest way to check whether two quotes are really offering the same performance. Ask any contractor for the AHRI number, then look it up yourself in the AHRI Directory (opens a new tab).
Manual J (Load Calculation)
The official definition: The Air Conditioning Contractors of America (ACCA) standard method for calculating a home's heating and cooling loads.
In plain English: We measure your rooms, windows, insulation and which way the house faces, and work out how much heating and cooling it actually needs.
Why it matters to you: It's how you get the right BTU and tonnage instead of a guess. If a quote doesn't mention one, ask how they sized the system. More in our guide to Manual J load calculations.
Duct Sealant
Also called: Mastic, or "pookie" in the trade.
The official definition: A paste or tape applied to duct seams and joints to stop air from leaking out.
In plain English: It's the gray goop we brush onto duct joints so the air you paid to heat or cool ends up in your rooms, not in the attic or crawlspace.
Why it matters to you: Leaky ducts waste energy and make some rooms hard to heat or cool. If a quote lists duct sealing, ask which ducts and how much.
Line Set
Also called: Refrigerant lines, lineset.
The official definition: The pair of copper tubes that carry refrigerant between the outdoor unit and the indoor coil.
In plain English: The two copper pipes, one usually wrapped in black foam, that run from the unit outside to the coil inside.
Why it matters to you: Old line sets may be the wrong size for a new system or contaminated from an old refrigerant. A quote should say whether it's reused, flushed or replaced, and longer runs need extra refrigerant.
Plenum
The official definition: A box or chamber attached to the furnace or air handler that collects or distributes air to the ductwork.
In plain English: The big sheet-metal box right on top of (or below) your furnace that connects it to the ducts.
Why it matters to you: A new furnace often doesn't line up with the old plenum. Replacing or modifying it is a common, legitimate line on a quote.
Supply and Return Ducts
The official definition: Supply ducts carry conditioned air from the system to the rooms. Return ducts carry room air back to the system.
In plain English: Supply vents blow air out. Return grilles, usually bigger, pull air back in. Your system needs both, like breathing out and breathing in.
Why it matters to you: Too few or too small returns is one of the most common problems we find. The system can't breathe, so it runs louder, hotter and less efficiently.
Static Pressure
The official definition: The resistance to airflow in a duct system, measured in inches of water column.
In plain English: It's the blood pressure of your duct system. High static means the fan is straining to push air through ducts that are too small, too restricted or too dirty.
Why it matters to you: A new system on ducts with high static pressure won't hit its rated efficiency and wears out faster. A good contractor measures it before quoting.
Short Cycling
The official definition: When a heating or cooling system turns on and off more frequently than designed.
In plain English: The system keeps starting and stopping every few minutes instead of running steady cycles.
Why it matters to you: It wastes energy, wears out parts and leaves the house uneven. The usual cause is an oversized system, though thermostat location and airflow problems can do it too.
Flue
Also called: Vent, exhaust pipe, chimney liner.
The official definition: A duct or pipe that carries combustion gases from an appliance to the outdoors.
In plain English: The pipe that takes the furnace's exhaust outside. On an 80% furnace it's metal; on a high-efficiency furnace it's PVC.
Why it matters to you: A flue that's the wrong size, damaged or shared with a water heater the wrong way can be a safety issue. It's one of the things inspectors check closely.
Combustion Air
The official definition: The air supplied to a fuel-burning appliance for the combustion process.
In plain English: A gas furnace needs fresh air to burn. It either pulls it from the room around it or through its own pipe from outside.
Why it matters to you: A furnace in a small closet without enough air can burn poorly and create carbon monoxide. Sometimes the fix is a louvered door or a dedicated pipe, and it's a code item.
Condensate Pump
The official definition: A small pump that removes condensate water from HVAC equipment when gravity drainage isn't possible.
In plain English: High-efficiency furnaces, air conditioners and heat pumps make water. If there's no floor drain lower than the unit, a little pump pushes the water to one.
Why it matters to you: When a condensate pump fails, the system can shut off or leak. It's a small part that's worth checking if your system stops for no clear reason.
Heat Strips
Also called: Electric heat, auxiliary heat, emergency heat, backup heat.
The official definition: Electric resistance heating elements installed in an air handler to supplement or replace heat pump heating.
In plain English: Heat strips are basically a giant toaster we blow a fan over. They're backup heat in case your heat pump can't keep up or stops working.
Why it matters to you: They're a very inefficient way to heat a home and should really only be used in emergencies. If you see "aux" or "emergency heat" on your thermostat often, call us; your power bill will notice.
Defrost Mode
The official definition: A heat pump operating mode that temporarily reverses the refrigerant cycle to melt frost from the outdoor coil.
In plain English: In cold, damp weather, frost builds up on the outdoor unit. Every so often the heat pump runs backwards for a few minutes to melt it off.
Why it matters to you: Steam rising from the outdoor unit in winter is normal. A unit that's encased in ice and stays that way isn't, and needs a look.
Permit and Inspection
The official definition: A permit is authorization from a local building department to perform regulated work. An inspection is the department's check that the work meets code.
In plain English: The city signs off that your install was done safely and to code.
Why it matters to you: Furnace, AC, heat pump and electrical work almost always needs a permit in the Denver metro. Skipping it can cause trouble with insurance or when you sell. Our quotes include the permit; ask if another quote doesn't.
Compressor
Also called: The heart of the system.
The official definition: The component that pressurizes refrigerant vapor and pumps it through the refrigeration cycle. Single-stage compressors run at one speed; two-stage at two; inverter (variable-speed) compressors adjust their speed continuously.
In plain English: The compressor is the pump inside the outdoor unit that keeps the refrigerant moving. An inverter compressor is like cruise control: it speeds up and slows down to match what your house needs, instead of slamming on and off.
Why it matters to you: The compressor is the most expensive part of an AC or heat pump. If it fails out of warranty, the repair can approach the cost of a new outdoor unit, which is often when replacing makes more sense. Inverter compressors are quieter, more efficient and better at holding a steady temperature, and they're what most cold-climate heat pumps use.
Air Handler
The official definition: The indoor unit of a heating or cooling system that contains the blower and coil, and circulates conditioned air through the ductwork.
In plain English: In a house with a furnace, the furnace does this job. In an all-electric heat pump system, the air handler takes the furnace's place: a box with a fan and a coil (and often heat strips) that pushes air through your ducts.
Why it matters to you: If a quote for an all-electric heat pump includes an air handler, that's what's replacing your furnace. Ask what backup heat it has and how big it is.
Mini-Split (Ductless)
Also called: Ductless heat pump, ductless AC, wall head, split.
The official definition: A heat pump or air conditioner with an outdoor unit connected by refrigerant lines to one or more indoor units mounted in the rooms they serve, without ductwork.
In plain English: An outdoor unit plus one or more indoor units, usually on the wall, connected by small pipes through the wall. No ducts needed.
Why it matters to you: Mini-splits are great for homes without ducts, additions, garages and rooms that are always too hot or cold. Each indoor unit (or "zone") has its own control. Our default mini-split brand is Kaden. Here's why.
Cold-Climate Heat Pump
The official definition: A heat pump that meets ENERGY STAR's cold-climate criteria, which set minimum efficiency and capacity at 5°F.
In plain English: A heat pump built to keep heating well when it's really cold out, not just in mild weather.
Why it matters to you: In Denver, this is the kind you want if a heat pump is going to do most of your heating. Most heat pump rebates, including Xcel's, require a qualifying cold-climate model, and Xcel pays per ton measured at 5°F.
Balance Point (Switchover Temperature)
The official definition: The outdoor temperature at which a heat pump's heating output equals the home's heat loss. Below it, supplemental heat is needed.
In plain English: The temperature where your heat pump can just barely keep up on its own. In a dual fuel system, the switchover temperature is the point where we tell the furnace to take over.
Why it matters to you: Where that switchover is set changes your gas and electric bills. It shouldn't be a factory default; it should be set based on your home's load calculation and your utility rates.
Filter and MERV
The official definition: MERV (Minimum Efficiency Reporting Value) rates how well an air filter captures particles, on a scale from 1 to 16 under ASHRAE Standard 52.2.
In plain English: The higher the MERV, the smaller the particles the filter catches. Most homes do well with something in the MERV 8 to 13 range.
Why it matters to you: Higher isn't automatically better. A very dense filter can choke the airflow on a system that wasn't designed for it, which raises static pressure and makes the system work harder. Change it on schedule, and ask us what your system can handle.
Zoning and Dampers
The official definition: A zoned system divides a home into areas controlled by separate thermostats, using motorized dampers in the ductwork to direct airflow to the zones that call for it.
In plain English: Dampers are little doors inside your ducts. With zoning, they open and close so the upstairs and downstairs (for example) each get their own thermostat.
Why it matters to you: Zoning can fix a house where one floor is always too hot or cold, but it only works with equipment and ductwork designed for it. A badly designed zone system can make things worse. Sometimes simple balancing does the job for much less.
Disconnect
Also called: Disco, fused disconnect, service disconnect.
The official definition: A switch that cuts power to equipment, required by the electrical code within sight of outdoor HVAC equipment so it can be shut off safely for service.
In plain English: The gray box on the wall next to your outdoor unit with a pull-out block or switch inside. It lets a technician turn the unit off right there.
Why it matters to you: A new outdoor unit often needs a new disconnect, and sometimes a new wire run, to meet current code. It's a normal line on a quote, not an upsell.
A2L Refrigerant
The official definition: An ASHRAE 34 safety class: "A" means lower toxicity, and "2L" means lower flammability. R-32 and R-454B are A2L refrigerants.
In plain English: The newer refrigerants are much better for the environment but can burn under the right conditions, so they're labeled "mildly flammable."
Why it matters to you: They're safe when installed correctly, but they come with new rules: some systems need leak detection sensors, and technicians need training and the right tools. It's part of why new equipment and installs cost more than they did a few years ago.
Ultra-Low NOx Furnace
The official definition: A gas furnace designed to emit no more than 14 nanograms of nitrogen oxides per joule of heat output, the limit set in Colorado for new furnaces sold since January 1, 2026 (unless ENERGY STAR certified).
In plain English: A furnace with a cleaner-burning design that puts out far less of the pollution that creates smog.
Why it matters to you: It's why the old standard 80% furnace mostly isn't an option in Colorado anymore, and why furnace prices went up. More in our guide to Colorado's furnace rules. Bigger homes may need a high-efficiency furnace because ultra-low NOx 80% models stop at 100,000 BTU input.
Superheat and Subcooling
The official definition: Superheat is the temperature of refrigerant vapor above its boiling point; subcooling is the temperature of liquid refrigerant below its condensing point. Both are measured to verify a system's refrigerant charge.
In plain English: Two readings a technician takes with gauges and thermometers to check that your system has the right amount of refrigerant.
Why it matters to you: Too much or too little refrigerant hurts efficiency and can damage the compressor. A good install, or a good tune-up, checks the charge with these readings, not by guessing or by feel.
Commissioning
The official definition: The process of testing and adjusting a newly installed system to confirm it operates as designed.
In plain English: After the install, we test it: airflow, gas pressure, refrigerant charge, temperatures and safety controls, and adjust until it's running right.
Why it matters to you: A system that's installed but never checked can run for years below its rated efficiency. Ask any contractor what readings they take before they leave.
B-Vent and the Wye Fitting
The official definition: B-vent is a double-wall metal vent pipe for standard (non-condensing) gas appliances. Where a furnace and water heater share a vent, code requires a properly sized connection, typically a wye rather than a tee.
In plain English: The metal exhaust pipe from an 80% furnace, and the Y-shaped fitting where the furnace and water heater exhausts join.
Why it matters to you: Old shared vents are one of the most common code updates when a furnace is replaced. It's a safety item, not an add-on.